A DXDR large deflection analysis of uniformly loaded square, circular and elliptical orthotropic plates using non-uniform rectangular finite-differencesKADKHODAYAN, M; ERFANI MOGHADAM, A; TURVEY, G. J et al.Journal of mechanical science and technology. 2012, Vol 26, Num 10, pp 3231-3242, issn 1738-494X, 12 p.Article

A cross-sectional analysis of composite beams based on asymptotic frameworkJEONG, Joonho; KIM, Jun-Sik; YEON JUNE KANG et al.Journal of mechanical science and technology. 2012, Vol 26, Num 1, pp 161-172, issn 1738-494X, 12 p.Article

A modified random decrement technique for modal identification from nonstationary ambient response data onlyLIN, Chang-Sheng; CHIANG, Dar-Yun.Journal of mechanical science and technology. 2012, Vol 26, Num 6, pp 1687-1696, issn 1738-494X, 10 p.Article

A numerical analysis of the effects of a stratified pre-mixture on homogeneous charge compression ignition combustionJAMSRAN, Narankhuu; OCK TAECK LIM.Journal of mechanical science and technology. 2012, Vol 26, Num 6, pp 1929-1935, issn 1738-494X, 7 p.Article

A numerical study of fluid flow and heat transfer in different microchannel heat sinks for electronic chip coolingSHANGLONG XU; GUANGXIN HU; JIE QIN et al.Journal of mechanical science and technology. 2012, Vol 26, Num 4, pp 1257-1263, issn 1738-494X, 7 p.Article

A numerical study of secondary flow and large eddies in a driven cavityYAU, Y. H; BADARUDIN, A; RUBINI, P. A et al.Journal of mechanical science and technology. 2012, Vol 26, Num 1, pp 93-102, issn 1738-494X, 10 p.Article

A study on the energy efficiency improvement of greenhouses: with a focus on the theoretical and experimental analysesLEE, Sung; KIM, Se-Hwan; WOO, Byung-Kwan et al.Journal of mechanical science and technology. 2012, Vol 26, Num 10, pp 3331-3338, issn 1738-494X, 8 p.Article

Accuracy improvement of indenting test results by using wireless cable indenting robotJANG, Kyung-Nam; KIM, Jong-Soeg; JEONG, Sun-Chul et al.Journal of mechanical science and technology. 2012, Vol 26, Num 9, pp 2735-2740, issn 1738-494X, 6 p.Article

Active vibration control of clamped beams using positive position feedback controllers with moment pairSHIN, Changjoo; HONG, Chinsuk; WEUI BONG JEONG et al.Journal of mechanical science and technology. 2012, Vol 26, Num 3, pp 731-740, issn 1738-494X, 10 p.Article

Adhesion strength in laminated glazings containing multilayer solar control coatingsAGUILAR, J. O; RODRIGUEZ-LELIS, J. M; DE LA FUENTE, M. Carrasco et al.Journal of mechanical science and technology. 2012, Vol 26, Num 6, pp 1725-1730, issn 1738-494X, 6 p.Article

An improved methodology for determining tensile design strengths of Alloy 617KIM, Woo-Gon; YIN, Song-Nan; PARK, Ji-Yeon et al.Journal of mechanical science and technology. 2012, Vol 26, Num 2, pp 379-387, issn 1738-494X, 9 p.Article

An investigation on effect of high pressure post injection on soot and NO emissions in a DI diesel enginePOORGHASEMI, Kamran; OMMI, Fathollah; YAGHMAEI, Hamed et al.Journal of mechanical science and technology. 2012, Vol 26, Num 1, pp 269-281, issn 1738-494X, 13 p.Article

Application of neural networks in evaluation of railway track quality conditionSADEGHI, Javad; ASKARINEJAD, Hossein.Journal of mechanical science and technology. 2012, Vol 26, Num 1, pp 113-122, issn 1738-494X, 10 p.Article

Characteristic flow patterns and aerodynamic performance on a forward-swept wingSAN, Kuo C; FEI, Yu F.Journal of mechanical science and technology. 2012, Vol 26, Num 10, pp 3103-3110, issn 1738-494X, 8 p.Article

Combining stress relaxation and rheometer test results in modeling a polyurethane stopperBANG, Kyukwon; JEONG, H.-Y.Journal of mechanical science and technology. 2012, Vol 26, Num 6, pp 1849-1855, issn 1738-494X, 7 p.Article

Crack tip shielding and anti-shielding effects of parallel cracks for a superconductor slab under an electromagnetic forceGAO, Zhi-Wen; KANG YONG LEE; ZHOU, You-He et al.Journal of mechanical science and technology. 2012, Vol 26, Num 2, pp 353-357, issn 1738-494X, 5 p.Article

Design of an optimal idle speed controller for a turbocharged diesel engine using fuzzy logic method ^tNIKZADFAR, Kamyar; NOORPOOR, Alireza; SHAMEKHI, Amir H et al.Journal of mechanical science and technology. 2012, Vol 26, Num 8, pp 2325-2336, issn 1738-494X, 12 p.Article

Detection of rubbing location in rotor system by super-harmonic responses ^tHONGLIANG YAO; QINGKAI HAN; LINGXUAN LI et al.Journal of mechanical science and technology. 2012, Vol 26, Num 8, pp 2431-2437, issn 1738-494X, 7 p.Article

Direct identification of non-proportional modal damping matrix for lumped mass system using modal parametersCHEONHONG MIN; PARK, Hanil; PARK, Sooyong et al.Journal of mechanical science and technology. 2012, Vol 26, Num 4, pp 993-1002, issn 1738-494X, 10 p.Article

Direct numerical simulation of rising bubble interaction with free surface using level contour reconstruction methodSHIN, Seungwon.Journal of mechanical science and technology. 2012, Vol 26, Num 10, pp 3141-3148, issn 1738-494X, 8 p.Article

Durability evaluation of a composite bogie frame with bow-shaped side beamsJUNG SEOK KIM; KWANG BOK SHIN; HYUK JIN YOON et al.Journal of mechanical science and technology. 2012, Vol 26, Num 2, pp 531-536, issn 1738-494X, 6 p.Article

Effect of channel and plenum aspect ratios on the performance of microchannel heat sink under different flow arrangementSEHGAL, S. S; MURUGESAN, Krishnan; MOHAPATRA, S. K et al.Journal of mechanical science and technology. 2012, Vol 26, Num 9, pp 2985-2994, issn 1738-494X, 10 p.Article

Effects of camber angle control of front suspension on vehicle dynamic behaviorsPARK, Seong-Jun; SOHN, Jeong-Hyun.Journal of mechanical science and technology. 2012, Vol 26, Num 2, pp 307-313, issn 1738-494X, 7 p.Article

Effects of inlet radius and bell mouth radius on flow rate and sound quality of centrifugal blower ^tNGOC SON, Pham; JAE WON KIM; BYUN, S. M et al.Journal of mechanical science and technology. 2012, Vol 26, Num 5, pp 1531-1538, issn 1738-494X, 8 p.Article

Effects of preloads on joints on dynamic stiffness of a whole machine tool structureMI, Liang; YIN, Guo-Fu; SUN, Ming-Nan et al.Journal of mechanical science and technology. 2012, Vol 26, Num 2, pp 495-508, issn 1738-494X, 14 p.Article